Looking for:
Spektrum dx6 manual download - |
Spektrum dx6 manual download -
Inhibit removes all trim bars and indicators from the Main Screen. Register your DX6 to get AirWare software updates and other news at spektrumrc. Ensure that the Page Update Airware Software 6. Before updating the sound files, make sure the transmitter battery is fully charged.
Failure to do so will result in the throttle moving to full throttle if failsafe activates. Move the Throttle stick until the cursor is near the point you wish to remove.
Scroll to Remove Pt. Page Mixing If you wish to assign a mix to a switch position: 1. Make sure you are in the desired mix screen. Move the switch you want to assign the mix to.
Scroll to the switch position where you want the mix to be active. Press the scroll wheel to activate the mix. When the box is filled, the mix is active. You can assign a mix to be active in multiple switch positions 0,1 or 2. An alarm sounds when the programmed time is reached.
You can Page Telemetry A variety of alerts can be chosen from the list, including telemetry alerts and a variety of flight conditions and commands. This is useful to verify programming functions, trim settings, mix directions, etc. The numeric value is directly relative to the travel adjust and mix values e. Page Acro Airplane Diagrams and setup names show on the transmitter screen to show the available setups. Refer to spektrumrc. Select wing and tail types before doing any other programming.
Use Elevator to Flap mixing to add the spoileron flight. Page Heli Helicopter 1. Select the Pitch Curve you wish to edit N, 1 or 2. Scroll right to select the points on the curve and edit the respective values. Page Swashplate Move the programmed cyclic or rudder channel, noting the throttle position. The throttle position should increase. If the throttle decreases, then the opposite value positive vs.
Diagrams and setup names show on the transmitter screen to show the available setups. Page Sail Mixing 3. Scroll to Diff: and press the scroll wheel once to change the value. Page Physical Transmitter Adjustments Tighten the opposite throttle strap to engage the desired throttle ratchet. Table of Contents. Previous Page. Next Page. Spektrum DX6i Programming Manual 4 pages.
Spektrum DX6i Assembly Manual 2 pages. Page 3 Timer The DX6i features ModelMatch technology that prevents the operation of a model if the wrong model memory is selected. During binding, the receiver actually learns and remembers the specific model memory 1 of 10 that the transmitter is currently programmed to.
For your convenience, this manual is arranged with separate sections for airplane and helicopter software However when using the DX6i with one of the Spektrum parkflyer receivers, like the AR, AR, ARE, functions. Also, unlike conventional radio systems that use 8 cells to power the transmitter, the DX6i uses 4 cells. This is due to the electronics being more efficient. Use the 2mm Allen wrench to loosen the setscrew. Then, turn the stick clockwise to shorten or counterclockwise to lengthen. Page 8: Receiver And Servo Installation In helicopters, there is generally enough room on the servo tray to achieve the necessary separation.
If necessary, a mount can be fashioned using clear plastic to mount the external receiver. Page 9: Range Check In gas- and glow-powered aircraft where vibration is present, the servos should be mounted using the supplied Before each flying session, and especially with a new model, it is important to perform a range check.
The DX6i rubber grommets and bushings. Do not over-tighten the mounting screws. Page Binding 5. Remove the bind plug from the charge jack before turning off the receiver and store it in a convenient place. Page Smartsafe Fail-Safe if used , power bus if used. Page Tips On Using 2.
Reduce photo to Page Aircraft Programming Guide The Throttle ALT function makes the throttle stick trim active only when the throttle stick is at less than half throttle. This allows accurate idle adjustments without affecting the mid to high throttle position.
The trainer switch is List List List located on the back left of the transmitter. Thank you in advance Alinco dx-r8 software program to use on my Alinco RX-R8. Hope to find one. All the best Bill Sony Interchangeable lens FE 50mm F2. Hamilton KB music stand Can't Open Name: Ben Rubenstein Barska Position Key Cabinet with Combo We have a key lock box, that seems to have come "locked" and i hear keys inside we haven't actually used it yet Does it come with an initial combination that needs to be reset?
I've tried the standard Blank screen. Just bought the house and it WAS working prior to my moving in PDF User Manuals. We regularly supplement and update our library. What our users say about us: Peter Morgan: "Thanks for this website! Thanks a lot. Totally happy!
SPECTRUM DX6 INSTRUCTION MANUAL Pdf Download | ManualsLib - Related Manuals for Spektrum DX6
Spektrum dx6 manual download. Spectrum DX6 Instruction Manual
Verify the switch selection is now displayed as desired. When correct, press the scroll wheel to select this switch and complete the switch selection. Page 9: Sd Card 1. Download the update from spektrumrc. Power off the transmitter and install the SD Card in the transmitter.
Power on the transmitter and the update automatically installs in the transmitter. Page Binding 4. Remove the bind plug from the receiver. Page Receiver Power System Requirements QuickConnect with Brownout Detection is designed to allow you to fly safely through most short duration power interruptions. However, you must correct the cause of these interruptions before your next flight to prevent a crash. Page Programming Failsafe Positions 2. Remove the bind plug when the orange LED on the main might advance to mid or full throttle.
The orange receiver LEDs will continue flashing. Page System Setup 1. Scroll to the desired model type and press the scroll wheel. The Confirm Model Type screen appears. Select Yes and press the scroll wheel to confirm the model type. All data will be reset. Page Spoken Flight Mode Setup 2. Scroll to the transmitter channel you wish to re-assign and press the scroll wheel. The box around the current input selection flashes.
Scroll left or right to select the desired control stick or switch. Press the scroll wheel to save the selection. Page Trim Setup 2. If you select Cancel, the system will return to the Model Select function. This allows accurate idle adjustments without affecting the mid to high throttle position. The trainer switch is List List List located on the back left of the transmitter.
The trainer switch is located on the back right on Mode 1 transmitters. The DX6i can memorize data for up to 10 release the roller.
Page 21 Rotate the roller to highlight the desired channel then press the roller to select that channel. The DX6i offers a Throttle Cut function. When the Throttle Cut button is pressed, the throttle moves to the low throttle, low trim position, allowing the safe and convenient shut down of the engine.
Page 24 Note: If INH is selected the aileron, elevator and rudder dual rate and expo functions independently operate using their respective switches. Page Model Select Reduce photo to Page 31 Press the roller to access the Model Select function. The DX6i features a memory function that stores the programmed data for up to 10 models.
A model name feature with up to eight characters allows each model to be easily identified. Page Dual Rate And Exponential The Dual Rate and Expo functions for aileron, elevator and rudder can be combined on a single switch conveniently allowing high or low rates to be selected via one switch.
Rotate the roller to highlight LIST then press the roller. The DX6i offers two programmable mixes that allow stick or switch inputs to control the output of two or more servos. This function allows mixing any one channel to any other channel, or the ability to mix a channel to itself.
Page 37 Using the roller, rotate to adjust the desired mixing values. After the desired value is programmed press the roller to deselect the value. When the Throttle Cut button is pressed, the throttle moves to a preprogrammed position low throttle, low trim allowing the safe and convenient shut down of the engine.
Page 54 With the transmitter already powered on and the main screen displayed, press and release the ROLLER to The DX6i features a memory function that stores the programmed data for up to 10 models. After that, your "Submit Link" or "Upload File" will appear. I tried to find it on my computer and had no success. Request for user manual. Thank you in advance Alinco dx-r8 software program to use on my Alinco RX-R8. Hope to find one. All the best Bill Sony Interchangeable lens FE 50mm F2.
Hamilton KB music stand Can't Open Name: Ben Rubenstein Barska Position Key Cabinet with Combo We have a key lock box, that seems to have come "locked" and i hear keys inside we haven't actually used it yet Does it come with an initial combination that needs to be reset? I've tried the standard Failure to exercise caution while using this product and comply with the following warnings could result in product malfunction, electrical issues, excessive heat, FIRE, and ultimately injury and property damage.
The transmitter comes with a thin, clear plastic film applied to some front panels for protection during shipping. Humidity and use may cause this film to come off. Carefully remove this film as desired. Digital Battery Voltage an alarm sounds and the screen flashes. D when battery charge gets down to 4. Press the scroll wheel to make a selection. Anytime the transmitter power is on, press the Clear and Back buttons to access the Model Select screen.
No radio transmission occurs when a System Setup screen is displayed, preventing accidental damage to linkages and servos during changes to programming. Press the scroll wheel once to display the Function List. Rolling and clicking the scroll wheel turns the selected box black, indicating that the value or condition will act on that position. To easily select a switch in a function, such as a program mix, roll with the scroll wheel to highlight the switch selection box, and press the scroll wheel.
The box around the switch should now flash. To select a switch, toggle the switch you wish to select. Verify the switch selection is now displayed as desired. When correct, press the scroll wheel to select this switch and complete the switch selection.
Power off the transmitter. Press the SD Card into the card slot with the card label facing the back of the transmitter. The card is keyed to fit in the case in only 1 direction. Do not use excessive force to install. Exporting the transmitter serial number to the SD Card allows you to copy and paste the serial number into the registration screen at spektrumrc.
Press and hold the scroll wheel while powering the transmitter on until the System Setup list appears. Scroll to the System Settings menu. Press the scroll wheel once to open the menu. Power off the transmitter and remove the SD Card from the transmitter. Insert the SD Card in your computer and open the.
Never power off the transmitter when updates are installing. Doing so may damage the system files. The update may erase all model files. For more information on AirWare software updates, visit spektrumrc. Download the update from spektrumrc. Power off the transmitter and install the SD Card in the transmitter. Power on the transmitter and the update automatically installs in the transmitter. The Select File screen appears.
Select the desired AirWare version from the File List. When updates are installing, the transmitter screen is dark.
The orange LED Spektrum bars flash and the update status bar appears on the screen. Doing so will damage the transmitter. You must bind the AR receiver to your transmitter before it will operate. The screen also provides binding information. Remove the bind plug from the receiver. While pressing the Bind button, power on the transmitter. This indicates the receiver is bound to the transmitter.
The transmitter screen also provides binding information. Inadequate power systems that do not provide the necessary minimum voltage to the receiver during flight have become the number one cause of in-flight failures.
Some of the power system components that affect the ability to properly deliver adequate power include:. The AR has a minimum operational voltage of 3. If you are using a questionable power system, e. Connect the voltmeter to an open channel port in the receiver and, with the system on, load the control surfaces apply pressure with your hand while monitoring the voltage at the receiver. The voltage should remain above 4. Ni-MH batteries charged with peak detection fast chargers have a tendency to false peak i.
This interrupts control, as the servos and receiver require a minimum of 3. QuickConnect with Brownout Detection is designed to allow you to fly safely through most short duration power interruptions. However, you must correct the cause of these interruptions before your next flight to prevent a crash. You establish failsafe positions when you bind your transmitter and receiver. If the radio signal connection is lost between the transmitter and receiver, the receiver immediately moves the aircraft control surfaces to the failsafe positions.
If you assign the receiverTHRO channel to a transmitter channel other than throttle, we recommend using Preset failsafe with the throttle in the low position. Always consult the receiver instruction manual for failsafe features. SmartSafe failsafe is a technology that only acts on the throttle channel and offers the following benefits:. To Program SmartSafe, move the throttle to the low or off position before putting the transmitter into bind mode.
Power the transmitter and receiver on. The throttle should immediately move to the failsafe position.
If the failsafe is not set correctly, your aircraft might. The Hold Last Command failsafe maintains the last command on all channels except throttle. If the radio signal is lost,the aircraft maintains the commanded control inputs until the receiver regains signal. To program Hold Last Command, follow the provided binding instructions in this instruction manual. Power on the transmitter and receiver. Move one of the control sticks to the desired Hold Last Command position and hold the input.
While holding the control input for example, a small amount of rudder power off the transmitter. The rudder should maintain the input command.
No comments:
Post a Comment